Updated Nov 22, 2026· 13 min read

Key takeaways

  • Compare five parts washers for garage and workshop cleaning, from compact 3.5-gallon benchtop tanks to 20-gallon cabinets, with sizes and pump specs.

A greasy gearbox, a varnished carburetor, or a set of oil-coated bearings needs a bath, not a rag, and a parts washer is the tub that does the work. A pump pushes cleaning fluid over the part while a brush scrubs away the grime, and the fluid drains back into the tank so it can circulate again. The five washers below cover the two sizes that suit most home garages: compact benchtop cabinets for small parts and 20-gallon floor units for larger engine work.

Our top pick: Red Sun 20-Gallon Parts Washer. Runner-up: JEGS 20-Gallon Parts Washer.

Every pick here is a solvent parts washer with a tank, a pump, and a work shelf or basket, and each one is sold for automotive parts such as wheel bearings, gears, and carburetors. Tank size, solvent capacity, and pump output are the figures that separate them, so this guide compares those numbers directly and flags the places where a listing states a figure in different units or does not state one at all.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

Quick Answer

For most garages, the Red Sun 20-gallon washer is the strongest all-around pick, with a 20-gallon tank and a 12-gallon solvent capacity for larger engine parts. The JEGS 20-gallon is the close alternative, with a higher stated pump output. For a small bench, the JEGS 5-gallon and the two 3.5-gallon cabinets cover bearings, gears, and carburetors.

Red Sun 20-Gallon Parts Washer

The Red Sun 20-gallon washer is the largest unit in this guide, and it is the pick for a garage that cleans engine parts often enough to justify a floor-standing tank. The tank holds 20 gallons, and the working solvent capacity is 12 gallons, so the fill sits well below the rim and leaves room to lower parts in without spilling fluid over the side. That working fill matters more than the headline tank size, because it is the amount of fluid the washer actually runs with.

An enclosed electric submersible pump recirculates the fluid, and the listing includes a flow-through brush with a 28-inch tube and a flexible spigot that directs the stream onto the part. The pump carries a filter that catches debris as the fluid circulates, so the same fill can be reused across several jobs. The listing names wheel bearings, gears, and carburetors, plus engine components and other oily parts: a 20-gallon tub takes parts that would never fit in a benchtop cabinet.

The listing recommends a water-based solvent, and buyers should follow that guidance rather than pouring in whatever fluid is already on the shelf. The washer runs on 110-volt, 60-hertz power and draws 0.23 amps, so it plugs into a standard household outlet in the garage. The listing gives a maximum pump output of 2.7 to 3.3 liters per minute in its specification table, so convert before comparing it with the gallon-per-minute figures below.

One limit is floor space: a 20-gallon floor unit is a fixture, so measure the spot beside the workbench before ordering and leave room to open the lid and lift parts out. The other limit is the fill itself: 12 gallons of cleaning fluid is a real purchase on top of the washer, and it needs safe storage between jobs.

Specs

    • Brand: redsun
    • Model: 09-04
    • Tank capacity: 20 gallons
    • Solvent capacity: 12 gallons
    • Pump: enclosed electric submersible pump with filter
    • Maximum pump output: 2.7 to 3.3 liters per minute
    • Power: 110V, 60 Hz, 0.23A
    • Item weight: 50.7 pounds
    • Material: alloy steel
    • Included: flow-through brush with 28-inch tube, flexible spigot
    • Recommended solvent: water-based solvent

    JEGS 20-Gallon Parts Washer

    The JEGS 20-gallon washer matches the Red Sun on tank size and solvent capacity, and it stands apart on pump output. Its tub holds 20 gallons with a 12-gallon solvent capacity, the same working fill as the Red Sun, and its listing states a maximum pump output of 2.64 to 3.17 gallons per minute. That is the highest stated pump output among the 20-gallon units in this guide, and it means a stronger stream over the part while the brush does its work.

    The body is heavy-duty steel with a powder-coated black finish, and the JEGS logo is printed on the tank. At 58 pounds it is the heavier of the two 20-gallon units, so it reads as a fixed station in the shop rather than a unit that moves between bays. The model number is 555-81525, and the listing presents it as a parts cleaner solvent tank for automotive work.

    There is no stated solvent type in the figures the listing publishes for this model, so check the manual for the fluids it allows before filling the tank. That check matters more on a 20-gallon unit than on a small one, because a wrong fill is 12 gallons to drain and dispose of rather than 3.5. The other practical check is the same as for the Red Sun: the washer needs a fixed spot with floor space around it, and the parts it cleans need to fit inside the tub. Measure the largest part first, then compare it with the tub, because a washer that cannot take the part is no help no matter how strong its pump is.

    Specs

      • Brand: JEGS
      • Model number: 555-81525
      • Tank capacity: 20 gallons
      • Solvent capacity: 12 gallons
      • Maximum pump output: 2.64 to 3.17 gallons per minute
      • Item weight: 58 pounds
      • Material: heavy-duty steel
      • Finish: powder-coated black with JEGS logo

      Red Sun 3.5-Gallon Parts Washer

      The Red Sun 3.5-gallon washer is the compact cabinet in this guide, and it is the pick for a bench that cleans small parts and has no floor space to spare. The tank holds 3.5 gallons, and the cabinet is built to sit on a workbench rather than on the floor, so it goes where the work already happens and it can be moved aside when the bench is needed for something else. The listing names wheel bearings, gears, and carburetors as the parts it cleans, and those are exactly the parts that fit a small cabinet: a bearing, a gear, or a carburetor body drops into the tank, soaks, and gets brushed clean without needing a 20-gallon tub.

      The listing presents it as a portable automotive parts cleaner in a blue cabinet, and the small tank is the point. A 3.5-gallon fill costs less than a 12-gallon fill, it is easier to carry to a disposal point, and it takes less bench space than a floor unit. The trade is capacity: only one or two small parts fit at a time, and a larger part such as an oil pan or a valve cover will not fit at all.

      One gap in the listing is the pump. The listing does not state a pump output figure for this model, so it cannot be compared with the Torin or the JEGS 5-gallon on flow. Buyers who care about flow should treat that as a missing figure, not as a low one, and compare this washer on size, portability, and tank capacity instead. The listing also does not publish a voltage figure in the details gathered for this guide, so check the listing before ordering if the outlet in the garage is a question. For small parts and a small bench, though, the washer does the job it is built for, and its size is its main strength.

      Specs

        • Brand: redsun
        • Capacity: 3.5 gallons
        • Type: portable cabinet parts washer
        • Color: blue
        • Parts named: wheel bearings, gears, carburetors
        • Pump output: not stated in the listing

        BIG RED Torin T10035 Parts Washer

        The BIG RED Torin T10035 is the second compact cabinet in this guide, and it is the one to pick when the buyer wants a stated pump figure on a small unit. The steel cabinet holds 3.5 gallons, it runs on a 110-volt electric pump, and the pump output is 1/2 gallon per minute. That is a modest flow, and it suits the size of the tank: a small cabinet needs a steady stream over a small part, not a torrent, and the half-gallon-per-minute flow keeps the fluid moving without splashing it out of a shallow tub. The maker is Torin, the brand is BIG RED, and the model is T10035.

        The red steel cabinet is built for the same parts as the Red Sun compact unit: bearings, gears, carburetors, and other small automotive components that fit inside a 3.5-gallon tank. For a buyer choosing between the two 3.5-gallon cabinets, the Torin gives the clearer specification sheet: tank size, voltage, and pump output are all stated, which makes it easier to judge before ordering.

        The limits are the same as for any 3.5-gallon cabinet. Only small parts fit, only one or two at a time, and a part that is larger than the tank needs a bigger washer or a different cleaning method. The pump output is also the lowest stated flow in this guide, so a part caked in thick grease will take longer under the brush than it would in the JEGS 20-gallon. That is a fair trade for a benchtop unit: it costs less to fill, it takes less space, and it handles the small parts that make up most home garage cleaning.

        Specs

          • Brand: BIG RED
          • Maker: Torin
          • Model: T10035
          • Capacity: 3.5 gallons
          • Pump: 110V electric pump
          • Pump output: 1/2 gallon per minute
          • Material: steel cabinet
          • Color: red

          JEGS 5-Gallon Parts Washer

          The JEGS 5-gallon washer sits between the compact cabinets and the floor units, and it is the pick for a bench that needs more room than a 3.5-gallon cabinet without giving up portability. The tank holds 5 gallons with a 3.5-gallon solvent capacity, so the working fill matches the full capacity of the two compact cabinets while the tank itself leaves headroom above the fluid. The listing states a maximum pump output of 3.96 gallons per minute, which is the highest stated pump output in this guide, and it comes from a freestanding portable unit rather than a floor cabinet.

          The body is steel, the unit is freestanding and portable, and the part number is 81526. At 17 pounds it is light enough to carry to the bench and put away after the job, and its listed dimensions are 14.25 by 17.38 by 8.75 inches, so it fits on a bench that would never hold a 20-gallon floor unit. A rocker switch controls the pump, and the unit is built for small parts and tools that need a wash before reassembly.

          The trade is depth. A 5-gallon tank with a 3.5-gallon fill takes small and mid-size parts, but it will not take the larger engine parts that fit the 20-gallon tubs. The stated pump output is high for the tank size, so expect a strong stream and keep the part low in the tank while the pump runs. The listing also leaves the fluid type to the manual, so check the fluids the maker allows before filling, just as with the 20-gallon JEGS. For a small garage that wants one washer for bearings, gears, carburetors, and the odd mid-size part, this is the most versatile unit in the guide.

          Specs

            • Brand: JEGS
            • Part number: 81526
            • Tank capacity: 5 gallons
            • Solvent capacity: 3.5 gallons
            • Maximum pump output: 3.96 gallons per minute
            • Item weight: 17 pounds
            • Product dimensions: 14.25 x 17.38 x 8.75 inches
            • Material: steel
            • Installation type: freestanding, portable
            • Control: rocker switch

            How to Choose

            Start with the largest part. Measure it, then match it to the tank. A 3.5-gallon cabinet takes bearings, gears, and carburetors. A 5-gallon tank adds room for mid-size parts. A 20-gallon tub takes larger engine parts, but even a 20-gallon tub has a limit, so the measurement comes before the order, not after. Tank capacity and solvent capacity are two different figures, and the solvent capacity is the one that decides how much fluid to buy: the 20-gallon washers here run on a 12-gallon fill, and the 5-gallon JEGS runs on a 3.5-gallon fill.

            Next, compare pump output in the same units. The JEGS 20-gallon states 2.64 to 3.17 gallons per minute, the JEGS 5-gallon states 3.96 gallons per minute at most, and the Torin states 1/2 gallon per minute. The Red Sun 20-gallon states 2.7 to 3.3 liters per minute, which is a different unit, and the Red Sun 3.5-gallon states no pump figure at all.

            Then check the space and the power. The 20-gallon washers are floor units that weigh about 50 to 58 pounds before they are filled, so they need a fixed spot with room to open the lid and lift parts out. The compact cabinets and the 5-gallon JEGS sit on a bench and weigh far less, so they suit a garage where the bench does double duty. The Red Sun 20-gallon and the Torin list 110-volt power, which runs on a standard household outlet. For any washer, check the listing for the power figure before ordering, and check the manual for the fluids the maker allows, because the fluid guidance differs by model and a wrong fill is costly to drain.

            Finally, look at the build. Steel tanks with a powder-coated finish resist rust from repeated contact with cleaning fluid, and all five washers here use steel construction. A work shelf or basket keeps parts off the bottom of the tank, and a filter in the pump line keeps debris out of the stream.

            Who Should Skip It

            Skip a parts washer if the parts are bigger than the biggest tank in this guide. A full engine block or a long exhaust component will not fit a 20-gallon tub, and forcing a part into a tank that is too small leaves half of it unwashed. Measure first, and if the part does not fit, a professional cleaning service is the better route. Skip it too if the cleaning job is tiny: a single bolt or a small bracket washes fine in warm soapy water with a brush, and a parts washer earns its bench space only when parts cleaning happens often.

            Skip a solvent parts washer if the job calls for a different cleaning method. Small precision parts with fine passages, such as a watch movement or a small carburetor jet, may suit an ultrasonic cleaner better, because sound waves reach into crevices that a brush and a stream cannot. A parts washer and an ultrasonic cleaner solve different problems, and buying the wrong one leaves the part dirty. Also skip a solvent washer if there is nowhere safe to store cleaning fluid or to dispose of used fluid. A 12-gallon fill needs a sealed container between jobs and a proper disposal route when it is spent, and a garage without that setup should not bring a solvent washer home.

            Frequently Asked Questions

            What size parts washer do I need?

            Match the tank to the largest part. A 3.5-gallon cabinet suits bearings, gears, and carburetors. A 5-gallon tank adds room for mid-size parts. A 20-gallon tub suits larger engine parts, with a 12-gallon working fill. Measure the largest part before ordering, because a part that does not fit the tank cannot be washed in it.

            What cleaning fluid can I use in these washers?

            Follow the maker for each model. The Red Sun 20-gallon listing recommends a water-based solvent, and its pump includes a filter that recirculates the fluid. For the other four washers, check the manual for the fluids the maker allows before filling the tank. Never pour gasoline or another flammable liquid into a parts washer, and store used fluid in a sealed container until it can be disposed of properly.

            How do the pump outputs compare?

            The figures use different units, so read them carefully. The JEGS 5-gallon states 3.96 gallons per minute at most, the JEGS 20-gallon states 2.64 to 3.17 gallons per minute, and the Torin states 1/2 gallon per minute. The Red Sun 20-gallon states 2.7 to 3.3 liters per minute in its specification table. The Red Sun 3.5-gallon states no pump output figure, so it cannot be ranked on flow.

            Can a parts washer clean a whole engine block?

            Only if the block fits inside the tank, and most blocks do not fit a 20-gallon tub. The 20-gallon washers here suit larger engine parts such as oil pans, valve covers, and transmission cases, but a full engine block is usually too large and too heavy for a home garage washer. Measure the block and the tub before ordering, and use a professional cleaning service for parts that do not fit.

            Conclusion

            The best parts washer is the one that fits the largest part, the bench, and the cleaning routine. For a working garage that cleans engine parts often, the Red Sun 20-gallon washer is the strongest all-around pick, with a 20-gallon tank and a 12-gallon working fill. The JEGS 20-gallon is the close alternative for buyers who want the highest stated pump output in a floor unit. For a small bench, the JEGS 5-gallon covers the widest range of small and mid-size parts, while the Red Sun 3.5-gallon and the BIG RED Torin T10035 cover bearings, gears, and carburetors in the least space. Measure the largest part, check the fluid guidance for the model, and pick the tank size that fits the work.

            Product and ASIN Reference

            Product ASIN
            Red Sun 20-Gallon Parts Washer B07XD16GLY
            JEGS 20-Gallon Parts Washer B078WJB4X2
            Red Sun 3.5-Gallon Parts Washer B07XGZTB2H
            BIG RED Torin T10035 Parts Washer B0026T75BA
            JEGS 5-Gallon Parts Washer B078WJ3QJB
            A
            affadmin
            We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best Parts Washers for Garage and Workshop Cleaning…Check price on Amazon

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free
            Prime for Young Adults

            A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

            See Prime for Young Adults
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free

            As an Amazon Associate we earn from qualifying purchases.